Plumbing Basics: An Essential for Installing a Bathtub
Plumbing Basics: An Essential for Installing a Bathtub
Blog Article
We have unearthed this great article about Installing A Bathtub directly below on the internet and reckoned it made perfect sense to share it with you on this page.
Setting up a bath tub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a moderately hard project. If the old tub is conveniently accessible, the job can relocate easily; if you have to open up a wall surface to get rid of the old bathtub and position the new bath tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will certainly require a helper to vacate the old bathtub and also set in the brand-new one. Ensure you have actually certified yourself for the work and also are comfortable attempting it. Rather than working with a professional to take over a halfway-completed task, it is much better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This short article will certainly help you set up a new tub in your restroom if you have currently bought a new bathtub and also don't need to transform the plan of your previous water supply pipes.
Your devices and material checklist should comprise the following:
Getting ready for the Installation
Firstly, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to avoid stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its last position.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the restricted accessibility that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the taps. Have a fabric ready for the staying water that will come from the pipes. When the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any type of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Installing the Bathtub
Using both wood boards under its feet, place the bathtub in the required setting. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bathtub until the spirit level reviews level.
To mount faucets, fit the bottom of the furthest versatile tap port to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Activate the water system and examine all joints as well as new pipework for leakages and tighten them if needed. Fill the bathtub and likewise check the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub must wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the producer provided backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The former kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath meets the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to break a rigid seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your components as well as installations. They are sold in tubes and also cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealant can crack relatively early if you do not take into account this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the market. It is a good idea to fit the ceramic tiles using waterproof or waterproof glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that blog post about How to Install a Bathtub Yourself when perusing the web. Are you aware of another individual who is involved in the subject? Feel free to promote it. Thanks for taking the time to read it.
Source This Article Report this page